How to Replace a Kia Sportage Replacement Key
The key in many Kia models comes with a keyless entry system built in. The key is usually akin to the remote control and is able to be replaced with a brand new one from an Kia dealer or locksmith.
Key fobs may stop working for several reasons, including a dead coin battery, worn buttons water damage, signal interference and a faulty receiver module. Here are some tips on how to get your Kia Sportage replacement key to work again.
How to replace the remote key or smartkey?
The battery in your Kia's intelligent key will eventually have to be replaced, whether it is a remote key, a push-to-start key or a normal metal key that is not equipped with a transponder. This is particularly when the car displays a message that the remote or smart key is not powered by the battery.
Luckily, this is quite simple to do. To replace the battery of the keyfob take out your mechanical key from the slit at the back of the fob. Then, pry the cover off. A small screw will be inside the key fob, which holds the battery in the correct position. Remove the old battery by unwinding the screw using the help of a small screwdriver. Insert the new battery and then close the cut on the key fob.
Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock in the same way, you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to go on errands around Brandon.
Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a computer, which is only available to the automotive locksmith or dealer. Other keys (non transponder keys made of metal), do not need programming. If your key requires to be reprogrammed, then you must be aware of the key code number written on the key code tag and save it in a safe location.
How do I replace the battery?
If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A low battery may cause other issues, such as the check engine light flashing or the engine not cranking properly. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just the most basic tools.
Before starting the process before beginning the process, ensure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece at the bottom of your key fob, and jiggle it until a metal key slides out. This key can be put into the door's driver handle to unlock your car.
To replace the battery inside the key fob, take off the cover that covers the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then position the new battery in a way that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.
Once the new battery has been installed after which you turn the key fob off and then turn it on in the ignition until the door locks. You can then test your Kia key fob and see whether it's functioning properly again.
How do you replace the smart key
You could have a standard keyfob, or a Smart Key based upon the model of Kia Sportage. The difference is that the smart key is equipped with a small mechanical key blade in it, whereas the standard fob does not. Both key fobs are equipped with batteries that eventually need to be changed. It is a simple process which takes just two minutes.
Make sure you turn off your Kia and be on a level, well-lit surface before you begin. Be aware that the fob contains tiny pieces that could fall if you're not careful.
The release button for the small size is located on the lower backside. It could be an oval or circular slot. You can open the key fob by pressing the button.
Once kia picanto key replacement is opened, take out the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done, your key fob should permit you to lock or unlock and start your vehicle, even if it isn't running.
How do I replace the mechanical key
The Kia keyfob is an excellent convenience that lets us lock or unlock our car with just pressing the button. Like any other device it will encounter issues at times. There are ways to resolve these issues and keep our key fobs in good working order over the long haul.
One of the most frequently encountered problems is a weak or dead battery. This can cause your device to stop working or work intermittently. If this happens then try replacing the battery with a new one.
If this does not solve the issue, try using the flathead screwdriver that is standard to wedge the fob's plastic casing open. Be careful not to damage internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.
Once the new battery is in, close and open the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to ensure it's working properly. Contact a dealer locksmith to address the issue if the fob is still not working. Make sure they cut you an emergency key that works in all the trunk and door cylinders to prevent lockouts in the future.